How to Make Wooden Pallet Benches

eHow may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

Overlooked, underutilized and habitually undervalued, simple wooden pallets are an absolute goldmine for the enterprising crafter looking to make something out of nothing. With a bit of handiwork, you can turn an average pallet into an eye-catching bench that's as inviting to the eye as it is comfortable for sitting.

Advertisement

Image Credit: Sonya Nimri

Video of the Day

Things You'll Need

  • Pallet

  • Crowbar

  • Hammer

  • Chop saw

  • Drill with countersink bit and Phillips head attachments

  • 2 1/2-inch screws

  • 1 1/4-inch screws

  • Measuring tape

  • T-square

  • Utility knife

  • Sandpaper, medium grit

  • Paint primer, 1 quart

  • Acrylic paint, various colors

  • Paintbrushes, various sizes

  • Plastic squeegee or scraper (an old credit card will work too)

Tip

Not every pallet is a good candidate for usage. If it is labeled HT, it means that it was heat-treated and safe to use. If the pallet is labeled MB, it has been treated with methyl bromide and is potentially toxic. So let's skip the latter and go with the former.

Step 1:

Pry the pallet apart with a hammer and crowbar, starting at the bottom of the pallet. Some of the boards may split. The bottom boards will not be needed, so it is OK if these split. Remove the loose nails as you work.

Advertisement

Video of the Day

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

Step 2:

Lay out all the top boards from the pallet (one-by-fours) to figure out how many you need to span the length of one pallet support (the scalloped two-by-fours). On this pallet, the pallet supports were 40 inches long.

Advertisement

Image Credit: Sonya Nimri

Step 3:

Use the chop saw to cut all of the top one-by-four boards in half to create enough pieces for the top of the bench. For example, in this project the top boards started off as six 30-inch long pieces and were chopped down to make 12 pieces that were 15 inches long. Of these 12 pieces, 10 of them were used for the bench top and two were used for the side skirts. Also, to fill in the gap for the bench top, one of the one-by-sixes (also from the top of the pallet) was cut down to 15 inches long and stuck in the middle of the one-by-fours as shown.

Advertisement

Advertisement

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

Step 4:

Lay two of the pallet supports (scalloped two-by-fours) parallel to each other with the notched sides down and the flat side up. Connect the two pieces together at one end by drilling one of the top one-by-four boards into the pallet supports. Use two screws on each side of the board. Repeat on the other end.

Advertisement

Tip

It is important to pre-drill holes with the countersink before putting screws in to avoid splitting the wood.

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

Step 5:

Fill in the remaining space between the pallet supports by attaching the rest of the one-by-fours. Use two screws to secure each side of the boards, spacing them evenly from the sides of the slats. In this project, the screws were drilled in about 5/8 inches from each side of the slat.

Advertisement

Advertisement

Image Credit: Sonya Nimri

Step 6:

Measure the inside gap between the pallet supports and then cut the last pieces of the one-by-fours to create a skirt for each side of the bench.

Advertisement

Image Credit: Sonya Nimri

Step 7:

Place one of the side skirts in the gap between the pallet supports and drill three screws from the top of the bench down into the side skirt, one at each end and one right in the middle. Repeat on the other side.

Advertisement

Image Credit: Sonya Nimri

Step 8:

Cut the last pallet support (scalloped two-by-four from the middle of the pallet) into four 10-inch long pieces, measuring and marking it first with a pencil.

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

Tip

The wood from one single pallet was used for this project, so the bench is only 10 inches high. If you want a higher bench, cut four pieces from two-by-fours to the length of your choice, 12 to 18 inches being a standard bench height.

Step 9:

Place the first leg under one corner of the bench top as shown. Use 2 1/2 inch screws in four places to secure it, making sure to pre-drill the holes first.

Advertisement

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

Tip

These screws will have to be drilled in at an angle because there is no space for the drill to fit under the lip of the bench.

Step 10:

Add a 1 1/2-inch screw through each side of the side skirts into each of the legs.

Image Credit: Sonya Nimri

Step 11:

Use a utility knife to carefully remove any large stray pieces of wood.

Image Credit: Sonya Nimri

Step 12:

Sand the bench with sandpaper to remove any splinters.

Advertisement

Image Credit: Sonya Nimri

Step 13:

Paint the bench with two coats of primer, allowing time to dry in between coats.

Image Credit: Sonya Nimri

Step 14:

Paint each plank of wood on the top of the bench a different color using acrylic paint. Hold a plastic scraper between the planks as you paint to keep the lines neat. Touch up any mistakes with fine-tipped paintbrushes. Paint the bench base with glossy white paint. Allow to dry.

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

This colorful pallet bench would look equally lovely outdoors or indoors.

Image Credit: Sonya Nimri
Image Credit: Sonya Nimri

Advertisement

Report an Issue

screenshot of the current page

Screenshot loading...